DINOSAUR ELECTRONICS HOME PAGE
IGNITOR BOARDS REPLACEMENTS for ONAN® OTHER PRODUCTS
REPLACEMENTS for DOMETIC® REPLACEMENT EYEBROWS COMPANY INFORMATION
REPLACEMENTS for NORCOLD® BOARD TESTERS WARRANTY INFO
CUSTOMER SERVICE
Dinosaur Electronic's
Ignitor Boards, Fan Control Boards and Accessories

*** IGNITOR BOARD USAGE CHART LINK ***

12 Volt DC Ignitor Boards
 Ignitor Board Features:

UIB S

  
Testing Engineers International have certified the 12 VDC UIB S, UIB S Post, UIB L, UIB L Post and the Fan 50 Plus Pins to

UL372 and UL353 specifications as they pertain to the RV Industry. With absolutely no changes, these are the same boards we have been selling for years.

Universal Ignitor Boards are for use in Furnaces, Refrigerators & Water Heaters.
  
The board comes ready for use in Furnaces or a jumper on the board can be cut to make the board instant fire for use in Refrigerators orWater heaters.

Water heater mounting kits and covers. are available.

Fan 50 Plus Pins For Suburban® and Atwood®/HydroFlame® furnaces with Fan Control Features. Can also be used to add Fan Control Features to other 12 VDC furnaces. Compatible with the Fan 50 Plus and UIB Fan control boards.

Ignitor Board Dimensions
The UIB S & UIB S Post: 3.25"x 4.25"
The UIB L & UIB L Post: 3.43"x 5.10"
Fan 50 Plus Pins: 3.25"x4.25"

 
  
*Superior Construction
"Plated and soldered through holes" to virtually eliminate intermittent connections. Click link for details.
*3 Try Tries 3 times to ignite gas, with appropriate purge cycles before going into lockout.
*Microcontroller  Highly reliable microcontroller for accurate and stable operation.

*Diagnostic LED  This light helps diagnose problems! GREEN-You have power to the board and NC terminal. RED-You have power to the gas valve terminal.

*Fuse protection Replaceable 5 Amp automotive fuse to protect the board from short circuits on the Valve and NC terminals.
*Made in the USA All of our circuit boards are made in the US with quality first, in mind. Every board is tested before packaging.
*Three Year Warranty Click here for Information on Dinosaur's Outstanding Warranty.

*** Propane is an explosive gas!
Ignitor boards should be installed by trained service technicians. ***
 
 
 
 

UIB S Post

UIB L

UIB L Post
Fan 50 Plus Pins
24 Volt AC Ignitor Boards
24 VAC Fan Control
24 VAC Operation with fan control
"For replacement of Park model furnaces with fan control"
Dimensions: 3.43" x 5.10"
UIB 24 VAC
 24 VAC Operation
"For Park model furnaces only"
Dimensions: 3.43" x 5.10"

Ignitor Board Kits and Accessories

TDR

  —New Product—
Our replacement Time delay relay is for use in older furnaces that use a standard 12VDC ignitor board.
The TDR has a 4 second delay before applying power to the fan motor, and a 2 minute cool down period at the end of the heat cycle before removing power from the fan motor.

AC/Gas Adapter Kit
4+6 Pin Adapter Board		 The AC/Gas adapter kit is for Atwood®/Hydroflame® water heaters that have a circuit board that uses both a 4 and a 6 pin edge connector to control both AC and Gas operations through a single thermostat. Includes the 2-tab mounting kit shown below. Click on the image for details.


2-Tab Mounting Kit
Adapter plate

 2-tab mounting kit for use in Atwood®/Hydroflame® water heaters. Mount a UIB S or UIB S Post without having to drill holes in the water heater to mount the board. Includes an adapter plate, small cover and mounting hardware.
UIB Series Covers

 Small and large covers for UIB Series Ignitor boards for use in Water heaters and refrigerators. Clear ABS covers allow you to see the diagnostic LEDs
* Fan control boards should not be used in DuoTherm® 900 series furnaces where the
thermostat is in the ground circuit unless the wiring has been modified to move the thermostat
to the positive side of the circuit. Click here for instructions